Ten-Tec
Ten-Tec 556 Argo QRP HF Transceiver 10-160 Meters with 20, 40, & 80 Meter Band Coils in Like New Condition
- MPN:
- 556
- Condition:
- Used
- Shipping:
- $38.00 (Fixed Shipping Cost)
Description
This Ten-Tec 556 Argo QRP HF Transceiver 10-160 Meters with 20, 40, & 80 Meter Band Coils in Like New Condition. It is virtually the same radio as the 555 Scout but is a QRP radio. (1 to 5 watts output)
This 556 Argo has very little time on the air. It belongs to a Ten-Tec Collector friend of mine who purchased it new and did not use it much if at all.
He has asked me to sell his collection as he is anticipating a move in the near future.
This Argo comes with the 20, 40, and 80 meter band coils.
The original manual and power cord is also included.
Ten-Tec did not provide a microphone with this radio. Any Dynamic 4 pin microphone will work.
Please check with me as I may have a microphone and matching 937 power supply in stock for this rig.
I am selling it as is, as described.
Included Band Modules:
-
Model 802, 80 meter plug-in band module
-
Model 803, 40 meter plug-in band module
-
Model 805, 20 meter plug-in band module
Specifications
General
-
MODES: CW, LSB, USB (Normal sideband for the band in use)
-
FREQUENCY RANGE: All ham bands 160 through 10 meters available through plug in modules. Overshoot at upper and lower edges.
-
DISPLAY: 4 digit to 100 Hz resolution, .56" LED.
-
FREQUENCY CONTROL: Permeability tuned oscillator (PTO) mixed with a crystal oscillator for each band.
-
OFFSET TUNING: +/- 1 KHz nominal – receive
-
FREQUENCY ACCURACY: +/- 100 Hz @ 25 deg. C.
-
ANTENNA: 50 ohms unbalanced.
-
POWER REQUIRED: @ 12-14 VDC: 600 ma receive, 2 A transmit @ 5 watts out, 1.3 A @ 1 watt out.
-
CONSTRUCTION: G 10 epoxy glass boards, most field replaceable. Molded plastic front panel, aluminum chassis, steel top and bottom.
-
DIMENSIONS: HWD 2.5" x 7.28' x 9.75" - 6.4 x 18.4 x 24.8 cm.
-
WEIGHT: 5 Ibs, 3 oz - 2.4 kg
Transmitter
-
RF OUTPUT: 5 watts, adjustable to 1 watt.
-
DC INPUT: 125 watts maximum @ 14 volts, SSB and CW duty cycle only.
-
MICROPHONE INPUT: 200 to 100K ohms, accepts microphones with 5 mv (-62db) output. Polarizing voltage provided for electrets.
-
T/R SWITCHING: PTT on SSB, QSK on CW.
-
IAMBIC KEYER: Adjustable 5- 50 WPM. Curtis type B, 15% fixed weighting.
-
CW OFFSET: 750 Hz
-
METERING: SWR or FWD power, rear panel switched.
-
SSB GENERATION: Balanced modulator, 9 pole crystal filter.
-
CARRIER SUPPRESSION: -45dB typical
-
UNWANTED SIDEBAND: -45 dB typical at 1.5 KHz tone.
-
THIRD ORDER INTERMOD: 30 dB below two tone @ 50 watts PEP.
Receiver
-
SENSITIVITY: .35 uV typical for 10 dB S+N/N @ 2.5 KHz bandwidth.
-
SELECTIVITY: "Jones" 9 pole crystal filter front panel adjustable 500 Hz to 2.5 KHz (Patent #5051711).
-
DYNAMIC RANGE: 85 dB @ 2.4 KHz bandwidth at 20 KHz spacing.
-
THIRD ORDER INTERCEPT: +1 dBm
-
NOISE FLOOR: -126 dBm typical
-
S-METER: Calibrated for 50 uV at S9
-
I-F FREQUENCY: 6.144 MHz
-
NOISE BLANKER: Optional plug-in board
-
AUDIO: 1 watt @ 4 ohms with less than 2% distortion
-
SPEAKER: 3 inch