Featuring Fine Vintage and Modern Amateur Radio Gear For Sale

ON Hold for Justin K. Ten-Tec Model 604 Iambic Electronic Keyer

Write a Review
MPN:
604
Condition:
Used
Shipping:
$10.00 (Fixed Shipping Cost)
  • Ten-Tec Model 604 Iambic Electronic Keyer
  • Ten-Tec Model 604 Iambic Electronic Keyer
$44.99
Frequently bought together:

Description

Ten-Tec Model 604 Iambic Electronic Keyer

This Keyer was tested and appears to be working.

 It is a part of a large Ten-Tec collection which has been stored and unused for many years so it may need some cleaning of contacts and potentiometers.

I am selling this keyer as is, as described.

Description

Torque drive dual paddles, developed by Ten-Tec, pivot on low friction ball bearings and have fully adjustable magnetic tensioning to custom fit the 604 to your touch. Paddle travel is adjusted through access holes in the cabinet. Paddle contacts are silver with gold plated keyer contacts. Front panel adjustment of speed and weighting. Full time dit and dah memories. Character speed range, 10 to 50 wpm. The top mounted button is a manual key-down control. A versatile keyer for any positive, low voltage circuit. Operates on 12 to 14 Vdc.

View AllClose

Related Products

Description The KR-20 provides crisp easy-to-copy CW at all speeds without operator fatigue. The paddle assembly incorporates a linear magnetic paddle return. Return force is adjusted by two front panel knobs which move magnetic shorting bars. Each paddle can be set individually to optimum tension. Paddles can be canted for the most comfortable position. Contact spacing is adjusted through holes in the top of the case. Specifications Keyed Time Base: Each character starts immediately when the paddle is actuated. A momentary closure of either paddle is all that is necessary to form a complete character. Weight Ratio: The traditional keyer has a dit-to-dah ratio of 1:3. A space has the same length as a dit. This dit-dah-space ration is fairly smooth at higher speeds, but becomes choppy at speeds below 25 wpm. Accordingly, we have incorporated a character-to-space ration extender to suit individual preference. The monitor, however, has the conventional 1:3 ratio. Monitor: A built-in monitor provides a side tone for feeding headphones or speaker. Volume and frequency of 600-1500 Hz is adjustable to suit the operator's taste. This also can be used for off-the-air code practice. For high impedance receiver input use a 220,000 ohm resistor in series with the monitor lead. Output: The output is handled by a reed relay. Rated at 15 volt-amps, it will key all regularly used keying circuits. The maximum keying voltage is 400 volts. Speed: A single control, tapered to provide linear adjustment, varies the speed from 6-60 words per minute. Electrical: The KR-20 circuitry is completely solide state. It emplys one dual JK integrated circuit, nine silicone transistors, and eight silicon diodes. power source is 105-125 volts at 0.125 amperes, 50-60 Hz. Push-on, push-off switch with pilot light. Line cord: 5'. Mechanical: The chasis is rigid steel. Cycolac® molded side panels have recessed wood grain finish. Nylon paddles are shaped for comfortable operation over long periods. Dimensions: 2-1/2" high x 4-3/4" wide x 8" deep. Weight: 2-1/2 pounds. Description The KR-20 provides crisp easy-to-copy CW at all speeds without operator fatigue. The paddle assembly incorporates a linear magnetic paddle return. Return force is adjusted by two front panel knobs which move magnetic shorting bars. Each paddle can be set individually to optimum tension. Paddles can be canted for the most comfortable position. Contact spacing is adjusted through holes in the top of the case. Specifications Keyed Time Base: Each character starts immediately when the paddle is actuated. A momentary closure of either paddle is all that is necessary to form a complete character. Weight Ratio: The traditional keyer has a dit-to-dah ratio of 1:3. A space has the same length as a dit. This dit-dah-space ration is fairly smooth at higher speeds, but becomes choppy at speeds below 25 wpm. Accordingly, we have incorporated a character-to-space ration extender to suit individual preference. The monitor, however, has the conventional 1:3 ratio. Monitor: A built-in monitor provides a side tone for feeding headphones or speaker. Volume and frequency of 600-1500 Hz is adjustable to suit the operator's taste. This also can be used for off-the-air code practice. For high impedance receiver input use a 220,000 ohm resistor in series with the monitor lead. Output: The output is handled by a reed relay. Rated at 15 volt-amps, it will key all regularly used keying circuits. The maximum keying voltage is 400 volts. Speed: A single control, tapered to provide linear adjustment, varies the speed from 6-60 words per minute. Electrical: The KR-20 circuitry is completely solide state. It emplys one dual JK integrated circuit, nine silicone transistors, and eight silicon diodes. power source is 105-125 volts at 0.125 amperes, 50-60 Hz. Push-on, push-off switch with pilot light. Line cord: 5'. Mechanical: The chasis is rigid steel. Cycolac® molded side panels have recessed wood grain finish. Nylon paddles are shaped for comfortable operation over long periods. Dimensions: 2-1/2" high x 4-3/4" wide x 8" deep. Weight: 2-1/2 pounds.
Add to Cart
Quick view

Ten-Tec Keyer Paddle Model KR20

Ten-Tec

$19.99
Ten-Tec Keyer Paddle Model KR20 This Keyer was tested and appears to be working but the paddles appear to need some adjustment.  It is a part of a large Ten-Tec collection which has been stored...
Ten-Tec Keyer Paddle Model KR-5 Ten-Tec Keyer Paddle Model KR-5
Add to Cart
Quick view

Ten-Tec Keyer Paddle Model KR-5

Ten-Tec

$34.99
Ten-Tec Keyer Paddle Model KR-5 This Keyer was tested and appears to be working.  It is a part of a large Ten-Tec collection which has been stored and unused for many years so it may need some...